In stock · 3 left 1 / 8

2016 - 2021 Toyota Prius 1.8L Inline-4 DOHC Hybrid Engine JDM 2ZR-FXE

Sale price $1,599.99
Delivery & pickup
  • California2–5 business days $130–$180
  • Other statesLower 48 · usually 6–8 business days $180–$400
  • Pickup in Chino, CAUsually ready in 24 hours Free

Shop Now, Pay Later

Make

Toyota

Fitment

2016 - 2021 Toyota Prius

Mileage

55K

Engine Design

1.8L, DOHC

Engine Type

Hybrid, Inline-4

Warranty

90 Days

4.9 129 Google reviews
90-day warranty On every unit
Compression tested Before it ships
Secure checkout Shop Pay, PayPal & cards
Feature Specification
Engine Code 2ZR-FXE (4th Generation / XW50 Spec)
Displacement 1.8 Liters (1,798 cc)
Configuration Inline-4 Cylinder (Atkinson Cycle)
Valvetrain DOHC, 16-Valve with VVT-i
Bore x Stroke 80.5 mm × 88.3 mm
Compression Ratio 13.0:1
Horsepower Output (Engine Only) ~95–98 hp @ 5,200 RPM
Torque Output (Engine Only) ~105 lb-ft @ 3,600 RPM
Fuel Delivery Multi-Point Electronic Fuel Injection (EFI)

Vehicle Fitment

This JDM 2ZR-FXE (4th-Gen) hybrid long block serves as a replacement for the following USDM 1.8L 4-cylinder hybrid models:

  • 2016–2022 Toyota Prius (L Eco, LE, XLE, Limited, Two, Three, Four — FWD & AWD-e)

  • 2017–2022 Toyota Prius Prime (Plug-In Hybrid)

USDM to JDM Swap Guide (2016–2021 Toyota Prius 2ZR-FXE)

Installing a JDM 2ZR-FXE engine into a USDM 4th-Gen Toyota Prius requires using the imported Japanese motor as a bare long block. Because Japanese right-hand drive (RHD) wiring harnesses, EGR cooler configurations, and emissions sensors differ from North American specifications, transferring your original USDM components guarantees a plug-and-play installation with zero Check Engine Lights (CEL).

1. Strip JDM Engine Down to Long Block: Preparation.

Unbolt and remove the Japanese wiring harness, external mounting brackets, intake manifold, EGR cooler assembly, and exhaust manifold from the JDM engine. Clean all cylinder head and block mating surfaces thoroughly.

Verification: Confirm the JDM engine is stripped down to the bare cylinder head, short block, timing chain cover, and oil pan assembly.

2. Transfer USDM Intake Manifold, EGR Cooler & Exhaust Assembly: Emissions & Intake Setup.

Unbolt your original USDM intake manifold (including electronic throttle body and MAP sensor), EGR valve/cooler assembly, and exhaust manifold with integrated heat exchanger piping, then install them onto the JDM engine using fresh OEM gaskets.

Verification: Visually inspect all intake, EGR, and exhaust port flanges to ensure a 100% airtight seal with no vacuum or coolant leak paths.

3. Swap USDM Engine Wiring Harness & Electric Water Pump: Electrical & Cooling Transfer.

Do NOT attempt to use the JDM right-hand drive wiring harness. Transfer your original USDM engine wiring harness and external components directly onto the JDM long block:

  • Electric Water Pump & Thermostat Housing Assembly

  • Camshaft & Crankshaft Position Sensors

  • VVT-i Oil Control Valve & Knock Sensor

  • A/C Compressor (Electric Hybrid Type) & Engine Mount Brackets

    Verification: Snap every connector from your USDM harness into its corresponding sensor port and confirm secure locking tabs without stretching any wires.

4. Install USDM Flywheel / Input Damper Assembly: Drivetrain & Dampener Prep.

Unbolt the JDM rear driveplate. Inspect the rear main crankshaft oil seal for any seepage and replace it if needed. Transfer your original USDM flywheel/transaxle input damper assembly onto the crankshaft flange using fresh threadlocker on the bolts.

Verification: Torque flywheel bolts to factory specifications in a star pattern and rotate the crankshaft 360 degrees by hand to confirm smooth operation.

5. Refill Fluids, Bleed Cooling System & Initial Startup: Final Installation.
  1. Lower the engine into the engine bay, mate it securely to the hybrid transaxle (eCVT), and torque all motor mounts.

  2. Fill the engine with fresh 0W-16 (or 0W-20) full synthetic motor oil and fill both the engine cooling system and inverter cooling loop with genuine Toyota Super Long Life Coolant (Pink).

  3. Reinstall the orange high-voltage service disconnect plug under the rear seat, sliding the lock tab firmly into place.

  4. Use a Toyota Techstream or capable OBD-II scan tool to activate Maintenance Mode (forcing the gas engine to run continuously) while bleeding trapped air from the cooling system.

    Verification: Confirm steady cabin heat, proper radiator fan cycling, and scan the hybrid ECU to verify zero diagnostic fault codes or Check Engine Lights (CEL).

All Star JDM offers limited warranty coverage on eligible used engines and transmissions. Used replacement engines and transmissions are generally covered for 90 days, while used performance engines and performance transmissions are generally covered for 30 days unless otherwise stated on the sales receipt. Rotary engines and parts are sold as-is with no warranty coverage.

The warranty covers eligible internal engine components, engine block, cylinder walls, and cylinder head against cracks or defects. External parts, electronics, accessories, improper installation, negligence, and installation-related failures are not covered.

Warranty claims require a written description, pictures, videos, and a valid report from a certified mechanic. Returned items must be in the same condition as sold, fully assembled, and include all original parts/components included in the sale.

For full details, please review our complete warranty policy.

JDM All Star offers a 30-day return policy, meaning customers have 30 days after receiving their item to request a return. Returned or refused orders may be subject to a 25% restocking fee, and original shipping charges plus return shipping costs are the customer’s responsibility.

Engines, transmissions, and automotive parts must be returned in the same condition as delivered. Returns will not be accepted if the item has been disassembled, modified, or parted out.

JDM All Star is not responsible for shipping damage, installation costs, labor, transport, or other related expenses. For return requests or questions, customers can contact sales@allstarjdm.com.

For full details, please review our complete refund policy.

All Star JDM offers specialized shipping with surcharges for services like liftgate delivery. They promise same-day shipping for orders before 1 PM PST, with next-day dispatch for later orders. Shipping is within the 48 contiguous states, with special arrangements for other US territories. Customers receive tracking numbers and are responsible for return shipping costs. Queries can be directed to their customer service. Shipping policy acceptance is required.

All Star JDM's terms require users to comply with conditions when using their website and services. It includes accepting terms upon access, being of legal age, and the right to refuse service. Information may not always be accurate, and service and prices can change without notice. They offer online-exclusive products, reserve order refusal rights, and may use third-party tools and materials. Users' feedback may be used freely, and personal information is protected under their Privacy Policy.

Local Free Delivery

Enjoy fast and free local delivery within 30 Miles getting your parts to you quickly and securely.

Installation Available

Need help with installation? We offer expert installation services to ensure your parts are fitted correctly and efficiently.

Warranty

Warranty Purchase with confidence—our parts come with a 90-day warranty non performance & 30 day on performance to guarantee your satisfaction and peace of mind.

Estimate freight to your door

  • No states found

Shipping to

Choose any shipping option at checkout.